非恒定增压式微尺度拉瓦尔喷管流动特性

针对微尺度喷流在航天器运动状态切换时出现的非恒定增压变化,采用直接模拟蒙特卡洛(DSMC)方法对阶跃式增压和线性式增压两种模式下的微尺度拉瓦尔喷管流场进行了模拟,并对其变化过程中的流动特性进行了对比分析。结果显示：阶跃式增压会导致流动特性出现较大幅值的峰谷式波动,而线性式增压下的流动特性则呈现出线性变化的特点;黏性力对微尺度喷流的非恒定增压变化产生了重要的黏滞作用,在喉部扩张段至出口的流场中尤为明显;在设定的条件下,阶跃式增压过程中喷流产生的总冲量较线性式增压高59.5%,质量流量高74.7%,单位工质提供的冲量低约8.6%,波动性也高于线性式模型,阶跃式增压适用于系统需要较大推力改变运动状态且推进剂充足的情况,而线性式增压在系统精确微调或需要推进剂产生更高效能时具有明显的优势。     

鸭式布局飞机矢量喷流对地面效应影响的风洞试验

针对单发鸭式布局飞机，通过低速风洞试验，研究了矢量喷流对飞机地面效应的影响特性。研究结果表明：发动机喷流使得飞机的地面效应增强，升力系数增加，降低飞机起飞/降落时的飞行速度，缩短起降距离，从而改善飞机起降性能。发动机喷管上/下偏转时，矢量喷流对飞机上下表面气流诱导不对称，均使地面效应阻力系数增量减小。在此基础上，基于数值模拟结果对喷流与地面效应的相互作用机理进行了分析。     

Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

圆心松弛的圆环格点阵及其灵敏度优化研究

针对目前综合孔径辐射计圆环格点阵圆心位置固定,不能最大程度利用圆环中可布阵区域的问题,提出圆环格点阵圆心优化方法,在不增大布阵区域的前提下,增加了布阵自由度,为阵列性能进一步优化提供了基础。基于圆心松弛的圆环格点阵,提出一种满足给定无混叠视场范围和空间角分辨率要求的广义圆环格点阵设计方法。基于广义圆环格点阵,当给定阵元数时,依据阵列退化因子优化灵敏度。仿真结果表明:优化后的阵列具有更高的辐射测量灵敏度。     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

飞行员疲劳监测中的人眼定位及状态判别研究

飞行员驾驶疲劳是影响飞行安全的重要因素之一。常用基于人眼识别的方法对飞行员进行疲劳监测，其关键是人眼定位及状态判别。利用改进的平均合成滤波器算法定位人眼，根据模糊综合评价思想，判定人眼睁开闭合状态，根据PERCLOS疲劳检测方法对飞行员进行疲劳监测。实验表明，改进的人眼定位方法具有更高的精确度和鲁棒性，提出的人眼状态判定方法能够满足疲劳监测需要。为最终构建一种机载的、实时的、非接触式的飞行员疲劳监测系统提供了理论基础。     

多段翼混合边界层改变对流场的影响研究

前缘缝翼尾流与主翼边界层混合的改变对主翼气动力具有重要影响.利用数值模拟手段,通过在前缘缝翼尾缘添加一定动量系数的喷流,改变前缘缝翼尾缘的尾流,进而改变尾流与主翼边界层的混合状况.求解二维多段翼模型30P30N在各个不同喷流条件下的二维非定常流场,结果表明:提高前缘缝翼尾缘喷流的动量系数,将使前缘缝翼尾流和主翼边界层混合开始点后移,提高主翼上表面负压峰值和主翼升力;混合开始点对主翼的负压峰值及升力均有一定的影响;增大来流攻角会抑制前缘缝翼尾流和主翼边界层的混合.     

基于快速非奇异终端滑模的姿态控制技术

针对存在执行器故障与外部干扰的刚体飞行器姿态控制系统,提出一种基于快速非奇异终端滑模(NSFTSM)的姿态容错控制方法.控制方法不仅保证姿态机动过程的快速性,而且避免了传统的终端滑模面所带来的奇异性问题.采用二阶鲁棒精确微分器估计执行器故障与外部干扰,采用快速非奇异终端滑模技术设计姿态容错控制律,根据Lyapunov稳定性理论证明了方法的稳定性.稳定性分析表明,通过引入新型快速非奇异终端滑模,控制器使得闭环系统能够快速收敛到滑模面的微小邻域内,进而收敛到系统平衡点的微小邻域内,并且系统对外部干扰具有较强的鲁棒性.数值仿真结果验证了方法在姿态跟踪控制中的有效性.